Introduction to how to play the claw machine

Played with many "catching doll" machines

Have you been "failed" countless times?

Have you never experienced the thrill of victory?

Do you always complain that this is an impossible task?

Catching dolls is actually a very necessary skill to master At the Big Gamer Fun Center.

I didn’t have three or four dolls on hand,Why are you embarrassed to say hello to others?

The strange girl crosses her eyes with admiration.

My own girl proudly walked through the crowd holding the doll

Definitely an affordable way to date.

Every time I catch a doll, I come back empty-handed.

I spent a lot of money on this! ! !

It’s really not because it’s too loose! There is a probability!

It's because you don't know the skills!

Read this guide

Come to the big player amusement center next time to play the claw machine

You won’t leave empty-handed!

Basic skill one

Basic Tip 1: About Clips

The clips of the claw machine usually consist of 3 pieces. When grabbing a doll, we often encounter that the angle of the claws is not as expected. When the clip is dropped, one of the claws will fall on the doll or deviate from the grasping point, so it is very important to rotate the clip.

Turning the clip is actually very simple, just quickly turn the joystick 360 degrees, the clip will rotate and swing, and the angle will change. When the clamp stops shaking, you can grab it, but you have to pay attention to the time. Turning the clamp is fun, but don’t get addicted~

Basic skill two

Basic Tip 2: About Buttons

Press the button once to make the clip fall, and press it again at the moment the clip catches the doll to increase the claw force. To be more specific, press it at 1/3 of the doll's height or when it is just enough to hold the entire doll. When the clip is completely in place, its natural strength to pick up the object will usually be insufficient. Most machines with strong claws will get stronger if you press them twice, but if they have weak claws, pressing once will be useless. It is actually useful for some machines, as it allows you to tighten the clamp at the precise moment, making it easier to catch. But be careful not to get excited. If you press the second button too early and the clip retracts in mid-air, it will be a disaster. Be careful~

Actual skill one

Practical Tip 1: Push the Doll Over

Pushing the doll down is a very practical technique. For larger dolls or dolls with two heads, it is best to grab the doll from the body and neck. If you clamp the doll from the head while it is sitting, the clamp will have no grip and the doll will easily fall off. The method is very simple, that is, drop the clamp slightly, put one claw on the head of the doll, and grab the body of the doll diagonally with the other two claws. After the clamp is retracted, the doll will be pulled down.

Note that the position must be mastered, and the rotating clamp can be used~ Also, if there are too many obstacles around the doll, this will not apply~

Actual skill two

Practical Skill 2: Throw the Clamp

First of all, the target doll cannot be too close to the glass or the acrylic of the exit, otherwise it will be knocked by the clamp. After confirming that there are no obstacles next to the target doll, swing the clip left and right to make the clip swing sharply left and right. Find the right time to press the drop button. After the claws catch the doll and retract it, the doll will be thrown towards the exit. Pay attention to calculate the falling position of the clip. After clamping the doll, normally the clip will not relax at this time. It will swing while retracting. When it reaches the top, the clip will usually let go, but our doll will also be thrown towards the hole haha. This method sounds very good, and it is safer than moving the clamp slowly, but it is difficult to aim, so the success rate is not high, and the landing point is very important.

Actual skill three

Practical Tip 3: Roll into the hole

This method is to have the doll clipped up and dropped, then roll directly into the hole. This method is very simple, but it requires observation first. Generally speaking, it is easier to roll in if the slope is more than 45 degrees, but it is more difficult if it is less than 30 degrees. The method is that when the clip falls, it should not be in a vertical line with the doll. The clip should be slightly closer to the hole, so that when the clip is recovered, it will have a pulling force toward the exit. This method is suitable for machines with low opening block height. It is best to use a small doll machine with a lot of dolls. You can pinch a few first to let him fill the hole, and then roll or use the previous method to push. It will be easier. If you don't want the child to trap the wolf, you will gain more by making some preparations first than pinching all the time.